| Author |
RGH2 with Matrix Glitcher |
wlintek
Registered: 2004-04-10
From: Australia
Messages: 61
Status: Offline
|   #30298 posted 2012-04-23 @ 04:12 GMT
since the RGH2 xsvf and jed files have been released, you can use them to program any xilinx based chip to glitch fat xbox360's that have dash 14717 or higher. i used matrix glitcher v1 and glitched a 14719 falcon. however, the boot time is not fantastic but it does boot from instant to 3-5 min. the A wire does not have to be a 50ohm coax cable, just use awg32 kynar wire and stick it as close as possible to the PCB on the GND area. the diagram is attached for those interested. for the matrix glitcher, the jumper needs to be on the FAT for all fat xbox's and no cap needs to be removed.
[ This message was edited by wlintek on 2012-04-23 @ 04:15 GMT ]
[ This message was edited by wlintek on 2012-04-24 @ 00:03 GMT ]
|
|
www.consoletronics.com a video game console specialist in sydney.
email:sales@consoletronics.com |
| Attachments: |  Phat_Diagram.jpg | | | |
 Profile
 pm
 www
 Quote
|
ssneeky10
Registered: 2005-04-01
Messages: 3
Status: Offline
| #30299 posted 2012-04-23 @ 05:26 GMT
You are a legend mate been trying for two days with matrix to do this and found no info what so ever.
Will try now thxs for your info again.
|
|
|
Profile
pm
Quote
|
ssneeky10
Registered: 2005-04-01
Messages: 3
Status: Offline
| #30300 posted 2012-04-23 @ 06:56 GMT
It worked but i didnt use a resistor but many thanks
|
|
|
Profile
pm
Quote
|
wlintek
Registered: 2004-04-10
From: Australia
Messages: 61
Status: Offline
| #30301 posted 2012-04-23 @ 07:57 GMT
it's good to know it worked for you. i tested with and without the resistor, it makes no difference.
|
|
www.consoletronics.com a video game console specialist in sydney.
email:sales@consoletronics.com |
Profile
pm
www
Quote
|
potel2
Registered: 2012-04-22
Messages: 3
Status: Offline
| #30302 posted 2012-04-23 @ 08:00 GMT
Thank you. I also was looking for this solution/confirmation that no cap should be removed.
|
|
|
Profile
pm
Quote
|
potel2
Registered: 2012-04-22
Messages: 3
Status: Offline
| #30303 posted 2012-04-23 @ 08:02 GMT
@wlintek
Which version of xsvf have you used for your Falcon? A, B, C or D?
I used B and C on a CB5772 Falcon, without success, yet.
[ This message was edited by potel2 on 2012-04-23 @ 08:47 GMT ]
|
|
|
Profile
pm
Quote
|
wlintek
Registered: 2004-04-10
From: Australia
Messages: 61
Status: Offline
| #30304 posted 2012-04-23 @ 11:28 GMT
Quote:
| On 2012-04-23 @ 08:02 GMT, potel2 wrote:
@wlintek
Which version of xsvf have you used for your Falcon? A, B, C or D?
I used B and C on a CB5772 Falcon, without success, yet.
[ This message was edited by potel2 on 2012-04-23 @ 08:47 GMT ] |
|
i used B version for falcon.
|
|
www.consoletronics.com a video game console specialist in sydney.
email:sales@consoletronics.com |
Profile
pm
www
Quote
|
ssneeky10
Registered: 2005-04-01
Messages: 3
Status: Offline
| #30305 posted 2012-04-23 @ 18:05 GMT
Ditto used file B for falcon on cb 5773
|
|
|
Profile
pm
Quote
|
potel2
Registered: 2012-04-22
Messages: 3
Status: Offline
| #30306 posted 2012-04-23 @ 19:39 GMT
Booted to Xell with C version of .jed on my CB5772 Falcon, using 32 cm of thin coaxial cable 50ohm on cpu_reset. Booted few times at about 2.5 minutes.
Now it doesn't boot on builded image.
I'm still working...
No resistor used. Anyway, resistor should be on cpu_rst line and not on stdby_clk as drawn in first post.
|
|
|
Profile
pm
Quote
|
wlintek
Registered: 2004-04-10
From: Australia
Messages: 61
Status: Offline
| #30307 posted 2012-04-24 @ 00:06 GMT
Quote:
| On 2012-04-23 @ 19:39 GMT, potel2 wrote:
No resistor used. Anyway, resistor should be on cpu_rst line and not on stdby_clk as drawn in first post.
|
|
yes, you are right, it was a mistake. i have correted the diagram. thanks for pointing out.
|
|
www.consoletronics.com a video game console specialist in sydney.
email:sales@consoletronics.com |
Profile
pm
www
Quote
|
wlintek
Registered: 2004-04-10
From: Australia
Messages: 61
Status: Offline
| #30435 posted 2012-06-21 @ 02:57 GMT
just did a jasper 16mb with 14719 dash. had to use falcon_b file to get a better glitch. now it boots from 3 seconds to 1min. most of the time around 10 seconds.
so anyone has problem in glitching, might just try all the 4 files and see which one works better for you.
|
|
www.consoletronics.com a video game console specialist in sydney.
email:sales@consoletronics.com |
Profile
pm
www
Quote
|
modrobert
Registered: 2003-10-17
From: Bangkok
Messages: 4903
Status: Offline
| #30436 posted 2012-06-21 @ 08:45 GMT
When using Matrix Glitcher II you can change the timing with the dip switches to emulate "RGH2" behavior, haven't tried it myself, but has been reported to work.
|
|
_____________________________ ____________ __________________ /\________
\ __________________ \ _____/____/ _ \ /_ /
/ / | l/ _/ ____) _/ _ \ \/ cREAM /
/______________l_______/ \______________\_______| \_ /________/
-+--Mo!-------------- \________/ ------------------- l_______/_____\ -----+- |
Profile
pm
www
Quote
|
